現代有卡說明書

1、前沿非常感謝您使用本公司產品。本手冊介紹了本產品的功能特點、安裝調試步驟、操作等。提出了因操作不當可能引起的意外事故及常見故障的排除方法和使用注意事項。在使用本產品前，請先仔細閱讀本說明書，以達到最佳使用效果。請妥善保存說明書并交最終使用者認真閱讀現代機械制造2014 年 9 月現代有卡旋切機特點：刀具鋒利，旋切精度高，刀片耐磨，裝卡牢固，該機型有自動壓桿和自動調刀裝置，不用人工壓桿，不脫刀，不蹦軸，并可自動調整刀高，壓尺可向后翻轉使刃磨刀具更加安全，方便，旋切出的單板平整度。均勻度、光滑度均達到國際標準，剩余木軸圓滑，粗細一致，該機旋切速度快，質量好，對操作要求低，節約木材，減少浪費，經濟高

2、效。一、機床的主要技術參數1、旋切刀的長度：2700mm2、壓尺長度：2730mm3、旋切圓木最大長度：2600mm4、旋切圓木最大直徑：1500mm5、旋切后圓木最小直徑：120mm6 主軸轉速：10-75rpm7、機床最大外形尺寸（長寬高）： 6000mm2250mm2300mm8、刀架快速移動速度：1120mm/min9、配用電機功率：（1）主電機：調速電機 YCT250-4B22KW夾緊電機：Y112M-4進給電機：Y112M-6小吊具電機：Y112M-44KW1.5KW3KW（5）數控進給電機：Y112M-410、機床總重量：約 7 噸2.2KW二、機床的吊運本機床吊運時，應確保安全

3、，按規定位置起吊，不得碰傷加工表面和油漆表面。三、機床的安裝本機床應安裝在平整的水泥地面上，要求地礎牢固，機床安放后，應找平機架，機床使用時應穩固可靠，必要時可以安裝地腳螺栓緊固。四、機床的調整及使用1、刀片的刃磨的角度 2122，如果旋切刀的厚度為 12.7mm，刃磨部分的寬度為 34mm 左右，刀片磨好后，必須用油石光刀刃。2、刀片安裝應以主軸中心水平高度為準，兩端高度必須完全一致。（刀刃至導軌上平面的距離為 165mm）3、校正壓尺棱與刀刃的平行度，并調整到理想的范圍。4、旋切過程中如出現脫刀（1）刀的高度太高，也可按調刀的上升按鈕，適當調節刀臺的角度。（2）壓尺棱與刀刃的平行度不好。5

4、、旋切過程中如出現蹦刀刀的高度太低，也可按調刀的下降按鈕，小導軌的后面的高度不能低于前端的高度。五、機床的潤滑和1、新設備使用前必須將主電速箱加機油 10 升左右。2、小吊車上的 2 個機，每個加機油 2 升左右。3、站內加油（有油標）4、所有鏈條、鏈輪、絲杠、絲母都應每班加機油或黃油潤滑。5、各運動旋轉部位每班加潤滑油一次。六、設備數控調整1、機械進給時，齒輪每個齒數的厚度為 0.875mm，例如旋切 0.30mm 的板皮，300.875=34，用 34 齒的齒輪即可。2、數控進給時，掛輪架用 54 齒的齒輪，如果屏幕上調刀 30.00 旋切后，板皮的實際厚度為 0.32mm，調節方法如下：

5、按向右的箭頭，屏幕最下端出現厚度系數，數字為黑色的130.0%，按 SET，讓黑色，（旋切后的實際厚度 32 除以屏幕上的 30 等于 1.066，用它乘以厚度系數 130.0%，得數為138.7%），按向上的家頭調到 138.7%，按綠色 ENT 鍵，再按紅色的 ESC 鍵退出即可。nk you very much for the use of the companys products.This manual describes the functions, the product installation anddebugging steps, etc. The accidentwas

6、causedbythe improperoperation and common troubleshooting methods and matters needingattention.Before using this product, please read this manual carefully, inorder to achieve the best results.Please keep this manual anduser to readThe Xiandai machinery manufacturing Co.,.2014 SeptemberThe front edge

7、Modern cardpeelingmachine, themachine tool issharp, cuttingpreci, toolwear, cled firmly, thems haveautomatic prerebar and automatictoolsetting device, withoutmanual prerebar, noknife, donot skip shaft, andcanautomatically adjustthecutterheight,prere gaugecan flipback to grinding the tool is more saf

8、e,convenient, veneer of smoothness.Evenness, smoothness areuptoernationalstandards, theremaining wood shaft smooth, uniformthickness, the cutting speed, goodquality, lowrequirementsforoperators,woodsaving, wastereduction, economic efficiency.One,The maechnical parameters, machine tool1, rotary cutte

9、r length: 2700mm2, prere gauge length: 2730mm3, theum length of rotary cutting logs: 2600mm4, peeling logum diameter: diameter 1500mm5, afteeling log minimum diameter: diameter 120mm6 spindle speed: 10-75rpm7,um size (length * width * height):6000mm * 2250mm * 2300mm8, Fast moving speed, tool: 1120m

10、m/min9, motorer:(1) the maotor: motor YCT250-4B 22KW(2) the cling motor: Y112M-4 4KW(3) the feed motor: Y112M-6 1.5KW(4) small lifting motor: Y112M-4 3KW(5) the CNC feed motor: Y112M-4 2.2KW10, the total weight of about 7 tons of machine tools:Two, machine tool liftingThis machine is hoisted, shall

11、ensure the safety,itionin accordancewith the provis of lifting, not hurt the machined surface and pasurface.Three, the installation of machine toolsThe machine should be installed on flat cement on the ground, thefoundation base, machinetool shouldbe placed after leveling, frame,machine tool use sho

12、uld be stable and reliable, it may be nesary toinstall theanchor bolts fastening.Four, adjust and use of machine tools1, the blade sharpening angle of 21 - 22 rotary cutter, if the thicknessof 12.7mm, the grinding part of the width isabout34mm, the bladesharpening, must use oil stone light blade.2,

13、theblade shouldbeinstalledhespindlecenter level level, heightmustbecompleyconsistent. (edge to guide plane distance is 165mm)3, the correction prere bar edge and edge paralleldegree, and adjustto the ideal range.4, rotary cutting proch as knife(1) the knife height is too high, can also according to

14、the ascendingbutton adjustable knife, knife angle adjusting.(2) prere bar edge and edge parallel degree is not good.5, rotary cutting jump knife such as prosKnife heightistoolow, itcanalsobe adjustable knife downbutton,behind the small rail height of not lessn the height of front end.Five, machine t

15、ool lubrication and maenance1, the new equipment must be the maotor and gearbox oil 10 liters.2 speed reducer 2, small crane, each with 2 liters of oil.3 hydraulic sion, hydraulic oil (oil standard)4, all the chain, sprocket, screw, nut should each of his oilrease.5, the movement of the roing parts

16、of every class lubricating oil a.Six, CNC equipment adjustment1, mechanical feed gear numberofteeth, each thicknessof0.875mm,such as rotary cutting 0.30mm plate, 30 / 0.875=34, with 34teeth gear can.2, CNCFeed, hangingwheelframe with the54gear, ifthescreen up-regulated afterrotarycutting knife 30, theactual thicknessof slab0.32mm, regulating methods are as follows: according to the rightarrow, atthebottomendof thethicknesscoefficient screen appears,digital black 130%, according to SET, let fadeto black, (