追信令流程

1、手機PS上網追信令流程：lh mp te config -run bus_send bus_receive NBAP_ASNlh mp te config -run bus_send bus_receive RANAP_ASNlh mp te config -run bus_send bus_receive RRC_ASN在rnc上輸入上述3條命令，然后輸入mon-mon mod根據最后給出的路徑，單獨開一個cigwin窗口，進入decoder目錄下面，按照下面的格式輸入： 提示的路徑及端口號 |tee ./文件名.raw | ./decoder.pl | tee ./文件名.dec | ./flow.pl -colour | tee ./文件名.flw2、PS 2/3G切換測試Trace流程：（追UE消息）路測的同時請抓取以下trace：在RNC中輸入（imsi號為測試手機號碼的imsi）：ueenable imsi 46000xxxxxx bus_send bus_receive trace1 trace3mon-mon mon lh modact(all RBS MOUDLE)注：在MOSHELL里用指令bo查看所有機框板子狀態，用指令pr iublink=RBSID查看該基站屬于的RNCmodule類型。在新開cygwin窗口，進入decoder目錄下面，根據mon命令顯示的路徑輸入：/home/yourid/moshell/monitor6054RNCip（如192.168.0.1） 33079（根據mon顯示的端口號碼） | tee ./文件名.raw | ./decoder.pl | tee ./文件名.dec | ./flow.pl -colour | tee ./文件名.flw測試結束后，在RNC中輸入uedisable all關閉decoder操作在RNC中輸入：lh mod te default3、用MOSHELL取kget all 文件。首先要打開MOMparsemom /home/youruserid/moshell/jarxml/tdrnc_node_mim_complete_A_20_1_CPP61LSV31.xml 然后用命令：kget all取出所有RNC配置信息。4、追NBAP消息lhsh te e bus_send bus_receive NBAP_ASNlhsh te e bus_send bus_receive RANAP_ASNlhsh te e bus_send bus_receive RRC_ASNlhsh te e bus_send bus_receive Ans_aal2ap_proc全網追蹤lh modact te e bus_send bus_receive NBAP_ASN lh modact te e bus_send bus_receive RANAP_ASN lh modact te e bus_send bus_receive RRC_ASN lh modact te e bus_send bus_receive Ans_aal2ap_procUE Tracelh modact teeallUEH_EXCEPTION lh modact teconfig-runbus_sendbus_receiveNBAP_ASNlh modactteconfig-runbus_sendbus_receiveRANAP_ASNlh modactteconfig-runbus_sendbus_receiveRRC*ueenableimsixxxxxxxxxxxxxxxxbus_sendbus_receivetrace1trace3trace5trace6trace7 mon-mon modacttrace跟蹤完后，運行：lh all te default 關閉traceUE Trace示例：WXRNC01 ueenable imsi 460023618218442（測試手機的IMSI） bus_send bus_receive trace1 trace3 trace5 trace6 trace7091018-16:32:23 5.31.240.1 7.1p TDRNC_NODE_MODEL_A_22_0 stopfile=/tmp/3768$ ueenable imsi 460023618218442 bus_send bus_receive trace1 trace3 trace5 trace6 trace70: imsi: imsi=460023618218442 check error info trace1 trace3 trace5 trace6 trace7 bus_send bus_receive interface object$ WXRNC01 mon-091018-16:32:54 5.31.240.1 7.1p TDRNC_NODE_MODEL_A_22_0 stopfile=/tmp/3768$ lhsh 001000 tm -disconnectAll monitored boards are disconnected and Target Monitor has shut down.$ WXRNC01 mon+ mod2 （2：為該基站所屬的RNC Module值，通過iublink得到，pr iublink或者get iublink= ）091018-16:33:17 5.31.240.1 7.1p TDRNC_NODE_MODEL_A_22_0 stopfile=/tmp/3768* Opening new handle:$ lhsh 001000 tm -tcp -win 1New monitor router process 0x492231 is started and listening to port 33077.To attach link handlers, use handle 1.New monitor router process 0x49222a is started and listening to port 33079.To attach link handlers, use handle 3.* Attaching boards to handle:$ lhsh 001000 tm -attach 3 011300To start the monitor client, run the following command (type h mon for more info):/home/Administrator/moshell/monitor6054 5.31.240.1 33079$moncommand = /home/Administrator/moshell/monitor6054 5.31.240.1 33079根據moncommand，新開一個cygwin窗口，輸入cd decoder進入decoder目錄下面，再：/home/Administrator/moshell/monitor6054 5.31.240.1 33079 | ./decoder.pl | tee ./log/WXTD2050C_091018.dec | ./flow.pl -colour |tee ./log/WXTD2050C_091018.flo.log后面為你要保存的文件名稱追完trace后，在RNC中輸入 uedisable all 關閉decoder操作在RNC中輸入： lh mod te default在RNC中輸入： uestatus all 查看RNC中ue trace狀態為活的手機$ uestatus all0: imsi: imsi=460023618218442 check error info trace1 trace3 trace6 trace7 bus_send bus_receive interface object1: imsi: imsi=460023618916615 check error info trace1 trace3 trace6 trace7 bus_send bus_receive interface objectWXRNC01 uedisable all091018-17:01:09 5.31.240.1 7.1p TDRNC_NODE_MODEL_A_22_0 stopfile=/tmp/3768$ uedisable alltrace condition 0 disabled.ueTrace is passive$2009/10/23 1. Get the log after enable the following traces in RNC and check whether the cell is delete and create automatically.lhsh xxxxxx te e bus_send bus_receive RRC_ASNlhsh xxxxxx te e bus_send bus_receive RANAP_ASNlhsh xxxxxx te e bus_send bus_receive NBAP_ASNlhsh xxxxxx te filter set 18 NBAP_ASN*lhsh xxxxxx te e bus_send bus_receive Ans_aal2ap_proclhsh xxxxxx te e all UEH_EXCEPTION xxxxxx means the RNC module which the cell located.新開窗口，cd decoder 然后：/home/XUPF/moshell/monitor6054 5.31.240.1 33079 | tee ./WXTD2038_091023.raw | ./decoder.pl | tee ./WXTD2038_091023.dec | ./flow.pl -colour | tee ./WXTD2038_091023.flw2009/10/271、RNC下抓TRACE：#General Trace Commandlh modmp te e bus_send bus_receive NBAP_ASNlh modmp te e bus_send bus_receive RANAP_ASNlh modmp te e bus_send bus_receive RRC_ASNlh modmp te filter set (18) NBAP_ASNlh modmp te e bus_send bus_receive RAB_ESTlh modmp te e bus_send bus_receive Ans_aal2ap_proclh modmp te e all UEH_EXCEPTION2、針對UE抓TRACE：#IMSI Trace Commandueenable imsi 460021531012360 bus_send bus_receive trace1 trace3 trace6 trace73、NODE B中抓TRACE：#Prepare traceall te default * all te default -restartall te log clear lh ru te d all measProclh ru te e bus_send bus_receive ccielh rax te filter set (323 AND 39 AND 310) ccielh rax te e bus_send bus_receive cciete d all eqcMtrTrMeasRouterCte filter set (323 AND 39 AND 310) CBCIte filter set (3131) CDCI_DBCCte filter set (347) CDCI_TRte filter set (327) AND 328 CDCI_TIMte filter set (18) NBAP*te e bus_send bus_receive CDCI*te e bus_send bus_receive CBCI*te e bus_send bus_receive NBAP*te e bus_send bus_receive BCMI te e bus_send bus_receive LRMI te e bus_send bus_receive EQMIte e bus_send bus_receive Ans_aal2ap_procte e all eqcArhAal2CepCte e all eqcArhAtmCepBoardHandlingCte e all eqcArhAtmResourceHandlerCte e all lrsRcCellCarrierC0te e all eqcRrhRadioResourceHandlerCte e rec_sig send_sig bus_send bus_receive state_change param bcCcmCommunicationContextCte e rec_sig send_sig bus_send bus_receive state_change bcCcmCommunicationContextManagete e rec_sig send_sig bus_send bus_receive state_change bcNphNbapDedicatedCte e rec_sig send_sig bus_send bus_receive state_change param lrsDchRadioLinkSetC#Monitormon 000100 000500 000600 000900#Restore to defaultall te default * all te default -restartall te log clear2009-11-3一. 如果現場發現PDP可以激活，但沒有流量的情況，追取以下log,不要全網追,可以專門對這個問題(定點)追.1,MPtraceslhteebus_sendbus_receiveRRC_ASNlhteebus_sendbus_receiveNBAP_ASNlhteebus_sendbus_receiveRANAP_ASNlhteeallUEH_EXCEPTIONlhteeallUE_IU_IF2,PDRtraceslhpdrteetrace2trace3SP_PMlhpdrteetrace3trace5DISCARD追完trace以后,將其全部關掉.在出現PDP激活后沒有流量的情況請安排追蹤以下trace。追完后，請將RNC上所有trace關掉。1、流量基站對應的ModuleMP板：lhsh xxxxxx te e bus_send bus_receive RANAP_ASNlhsh xxxxxx te e bus_send bus_receive NBAP_ASN lhsh xxxxxx te e bus_send bus_receive RRC*lhsh xxxxxx te e bus_send bus_receive Ans_aal2ap_proc*lhsh xxxxxx te filter set 108AND118 NBAP_ASNlhsh xxxxxx te e all UEH_EXCEPTIONueenable imsi xxxxxxxxxxxxxxx2、在相應ModuelMP板對應的2塊SPB板上分別追sp1-4的trace：該SPB板可get ModuelMP看到lhsh 022200/sp1.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022200/sp2.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022200/sp3.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022200/sp4.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022300/sp1.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022300/sp2.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022300/sp3.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UElhsh 022300/sp4.lnh te e bus_send trace1 trace2 trace3 trace4 trace5 trace6 trace7 RLC_UP_CONTROL_DL_UE lhsh 022200/sp1.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022200/sp2.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022200/sp3.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022200/sp4.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022300/sp1.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022300/sp2.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022300/sp3.lnh te e bus_receive RLC_UP_CONTROL_UL_UElhsh 022300/sp4.lnh te e bus_receive RLC_UP_CONTROL_UL_UE lhsh 022200/sp1.lnh te e all RETRANSM_UElhsh 022200/sp2.lnh te e all RETRANSM_UElhsh 022200/sp3.lnh te e all RETRANSM_UElhsh 022200/sp4.lnh te e all RETRANSM_UElhsh 022300/sp1.lnh te e all RETRANSM_UElhsh 022300/sp2.lnh te e all RETRANSM_UElhsh 022300/sp3.lnh te e all RETRANSM_UElhsh 022300/sp4.lnh te e all RETRANSM_UE lhsh 022200/sp1.lnh te e all DISCARD_UElhsh 022200/sp2.lnh te e all DISCARD_UElhsh 022200/sp3.lnh te e all DISCARD_UElhsh 022200/sp4.lnh te e all DISCARD_UElhsh 022300/sp1.lnh te e all DISCARD_UElhsh 022300/sp2.lnh te e all DISCARD_UElhsh 022300/sp3.lnh te e all DISCARD_UElhsh 022300/sp4.lnh te e all DISCARD_UElhsh 022200/sp1.lnh te e all SP_EXCEPTIONlhsh 022200/sp2.lnh te e all SP_EXCEPTIONlhsh 022200/sp3.lnh te e all SP_EXCEPTIONlhsh 022200/sp4.lnh te e all SP_EXCEPTIONlhsh 022300/sp1.lnh te e all SP_EXCEPTIONlhsh 022300/sp2.lnh te e all SP_EXCEPTIONlhsh 022300/sp3.lnh te e all SP_EXCEPTIONlhsh 022300/sp4.lnh te e all SP_EXCEPTION二. 對于PDP有時可以激活,有時無法激活的情況,請選擇一個基站作以下trace,作完后將所有trace關掉(all te default).1,開啟UEimsitrace:-ueenableimsitrace6trace7bus_sendbus_receive2,在相應Module的SPB板上開以下trace(如對應Module10的兩塊SPB為012200和012300):lhsh012200/sp1.lnhueenablealllhsh012200/sp2.lnhueenablealllhsh012200/sp3.lnhueenablealllhsh012200/sp4.lnhueenablealllhsh012300/sp1.lnhueenablealllhsh012300/sp2.lnhueenablealllhsh012300/sp3.lnhueenablealllhsh012300/sp4.lnhueenableall3,在對應的ModuleGPB上開啟以下trace(如Module10):lhshmod10teetrace3trace4trace6trace7UE_GENERALlhshmod10teebus_sendbus_receiveUE_ASN_RRClhshmod10teebus_sendbus_receiveUE_ASN_NBAPlhshmod10teebus_sendbus_receiveUE_ASN_RANAPlhshmod10teetrace3trace6trace7UE_RAB_ESTlhshmod10teetrace4trace6trace7UE_GENERALlhshmod10teebus_sendbus_receiveAns_aal2ap_proclhshmod10tefilterset18NBAP*lhshmod10teeallUEH_EXCEPTIONlhshmod10teeallIU_IF/mod10如果lhsh連接不上，則用bp mod10得到該module的板號，再lhsh該板號4,在對應的SPB上開以下trace(如module10對應的兩塊SPB):lhsh012200teeallSP_EXCEPTIONlhsh012300teeallSP_EXCEPTIONlhsh012200teebus_receiveSP_CONFIG_UElhsh012300teebus_receiveSP_CONFIG_UE2009-11-23 rrcConnectionReject1、針對rrcConnectionReject的問題，可以對單站追下列Trace，能看到rrcConnectionReject信息Failed to encode RRC message 抓取下列Trace： RRC_ASN bus_send, bus_receiveuehUeCtxtC* 1,3, 6,7, enter, returnlh mod42 te e bus_send bus_receive NBAP_ASNlh mod42 te e bus_send bus_receive RANAP_ASNlh mod42 te e bus_send bus_receive RRC_ASNlh mod42 te filter set (18) NBAP_ASNlh mod42 te e bus_send bus_receive RAB_ESTlh mod42 te e bus_send bus_receive Ans_aal2ap_proclh mod42 te e all UEH_EXCEPTIONlhsh 121400 te e trace1 trace3 trace6 trace7 uehUeCtxtC*mon-mon+ mod42/home/XUPF/moshell/monitor6054 5.31.240.1 33079 | tee ./WXTD2017_091123.raw | ./decoder.pl | tee ./WXTD2017_091123.dec | ./flow.pl -colour | tee ./WXTD2017_091123.flwlhsh 121400 te e bus_send bus_receive NBAP_ASN lhsh 121400 te e bus_send bus_receive RANAP_ASNlhsh 121400 te e bus_send bus_receive RRC_ASNlhsh 121400 te e all UEH_EXCEPTION lhsh 121400 te e bus_send bus_receive Ans_aal2ap_proc*lhsh 121400 te e trace1 trace3 trace6 trace7 uehUeCtxtC*2009-12-29 基站Trace小區建立的trace，先將小區閉掉，然后開啟，追建立過程的trace:在基站的moshell上輸入：tedefaultteebus_sendbus_receiveCDCI*teebus_sendbus_receiveCBCI*teebus_sendbus_receiveNBAP*mon-mon000100/opt/ericsson/amos/moshell/monitor6054 174.31.0.169 33079 | tee ./WXTD2008_091229.raw本地Trace解碼：從網管上下載RAW文件WXTD2008_091229.raw到本地的decoder目錄下，進入moshell下的decoder目錄，輸入：cat WXTD2008_091229.raw|./decoder.pl|tee WXTD2008_091229.dec|./flow.pl -colour | tee WXTD2008_091229.flw2010-01-04 遇到多RRU級聯，第二個RRU通道起不來可以在基站上抓下列Trace：te default *te default -restart *te e bus_send bus_receive NBAP*te e all Ans_aal2ap_procte e bus_send bus_receive CDCI*te e bus_send bus_receive CBCI*te e bus_se