【BS英國標準word原稿】BSEN12693-2008Refrigeratingsystemsandheatpumps.Safetyandenvironmentalrequirements.Positivedisplacementrefrigerantcompressors.doc

，如果你需要更多標準可以到/kmust1進行免費查閱。 如果你購買的文檔存在缺頁、字跡模糊、亂碼等情況，請大家通過論壇消息與我聯系。british standardbs en12693:2008refrigerating systems and heat pumps safety and environmental requirements positive displacement refrigerant compressorsics 23.140; 27.080 bs en 12693:2008national forewordthis british standard is the uk implementation of en 12693:2008.the uk participation in its preparation was entrusted to technical committeerhe/18, refrigeration safety.a list of organizations represented on this committee can be obtained on request to its secretary.this publication does not purport to include all the necessary provisions of a contract. users are responsible for its correct application.compliance with a british standard cannot confer immunity from legal obligations.this british standard was published under the authoritystrategy committee on 31 july 2008 bsi 2008isbn 978 0 580 57424 5amendments/corrigenda issued since publicationdatecommentseuropean standard norme europenneeuropische normen 12693may 2008ics 23.140; 27.080english versionrefrigerating systems and heat pumps - safety and environmental requirements - positive displacement refrigerant compressorssystmes de rfrigration et pompes chaleur - exigences de scurit et denvironnement - compresseurs volumtriques pour fluides frigorignesklteanlagen und wrmepumpen - sicherheitstechnische und umweltrelevante anforderungen - verdrngerverdichter fr kltemittelthis european standard was approved by cen on 25 april 2008.cen members are bound to comply with the cen/cenelec internal regulations which stipulate the conditions for giving this european standard the status of a national standard without any alteration. up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the cen management centre or to any cen member.this european standard exists in three official versions (english, french, german). a version in any other language made by translation under the responsibility of a cen member into its own language and notified to the cen management centre has the same status as the official versions.cen members are the national standards bodies of austria, belgium, bulgaria, cyprus, czech republic, denmark, estonia, finland, france, germany, greece, hungary, iceland, ireland, italy, latvia, lithuania, luxembourg, malta, netherlands, norway, poland, portugal, romania, slovakia, slovenia, spain, sweden, switzerland and united kingdom.european committee for standardization c om i t eur op en de nor m al i s ati on eur op i s c hes kom i tee f r nor m ung management centre: rue de stassart, 36 b-1050 brussels 2008 cenall rights of exploitation in any form and by any means reserved worldwide for cen national members.ref. no. en 12693:2008: ebs en 12693:2008en 12693:2008 (e)contentspageforeword.3introduction .41scope .42normative references .53terms and definitions .73.6symbols .84list of significant hazards .105safety requirements and/or protective measures .125.1general.125.2protection of moving parts .125.3safety to prevent loss of stability .125.4safety during handling .125.5safety to prevent rupture or bursting .125.6electrical safety.145.7measures to reduce emissions of substances .166verification of safety requirements and/or protective measures .166.1general.166.2type test .176.3individual test .197marking, graphical symbols, written warnings.207.1general.207.2marking .217.3graphical symbols, written warnings and information.228documentation and information for the user .228.1general.228.2instruction handbook .22annex a (informative) basic design criteria for refrigerant compressors .24annex b (normative) procedure for the design of a refrigerant compressor .25annex c (normative) materials .28annex d (normative) determination of the allowable pressure at the maximum operatingtemperature .30annex e (normative) determination of the allowable pressure at minimum operating temperature(requirements to avoid brittle fracture) .31annex f (informative) compilation of material characteristics of often used materials .37annex za (informative) relationship between this european standard and the essentialrequirements of eu directive 98/37/ec .61annex zb (informative) relationship between this european standard and the essentialrequirements of eu directive 2006/42/ec .62bibliography .639forewordthis document (en 12693:2008) has been prepared by technical committee cen/tc 182 refrigerating systems, safety and environmental requirements, the secretariat of which is held by din.this european standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by november 2008, and conflicting national standards shall be withdrawn at the latest by november 2008.this document has been prepared under a mandate given to cen by the european commission and theeuropean free trade association, and supports essential requirements of eu directives 98/37/ec and2006/42/ec.for relationship with eu directive(s) see informative annexes za and zb, which are an integral part of this document.attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. cen and/or cenelec shall not be held responsible for identifying any or all such patent rights.according to the cen/cenelec internal regulations, the national standards organizations of the following countries are bound to implement this european standard: austria, belgium, bulgaria, cyprus, czech republic, denmark, estonia, finland, france, germany, greece, hungary, iceland, ireland, italy, latvia, lithuania, luxembourg, malta, netherlands, norway, poland, portugal, romania, slovakia, slovenia, spain, sweden, switzerland and united kingdom.introductionthis standard is a type c standard as stated in en iso 12100.the machinery concerned and the extent to which hazards, hazardous situations and hazardous events are covered are indicated in the scope of this standard.when provisions of this type c standard are different from those which are stated in type a or b standards, the provisions of this type c standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type c standard.1scopethis standard applies to positive displacement refrigerant compressors for stationary and mobile refrigerating systems and heat pumps defined in 3.1, hereafter called compressors.it applies for compressors used in commercial and industrial appliances and with electrical energy supply including integral motors, up to 1 000 vac and 1 500 vdc.it applies to open drive, semi hermetic and hermetic motor compressors, which contain a positive compression function.this standard is not applicable to: compressors used in household appliance for which en 60335-2-34 applies; compressors using water or air as refrigerant.this standard does not deal with requirements for vibration and noise.note 1compressors for automotive comfort air conditioning systems can be developed according e.g. sae j 639. note 2noise emission depends on the complete installation of the built-in compressors and the correspondingoperating conditions.for semi-hermetic and open drive compressors which include moving parts and for which the external envelope is primarily designed for mechanical loads, thermal loads (to limit the possible deformation due to temperature), stiffness of the structure (external mechanical loads and weight of the equipment), taking into account established safe industrial practice, it is considered that pressure is not a significant design factor.attached parts covering other functions e.g. oil separators, oil coolers, suction accumulators shall comply to en 14276-1 or en 13445-6 (cast iron) or en 13445-8 (aluminium) or showing compliance to the relevant european requirements. this applies also to shells for hermetic compressors either welded or with any kind of permanent joint.requirements for compressors used in explosive atmospheres are not covered by this standard.note 3for further guidance see en 13463-1.this standard deals with all significant hazards, hazardous situations and events relevant to compressors, when they are used as intended and under conditions for misuse which are reasonably foreseeable by the manufacturer (see clause 4).this standard specifies safety requirements for the design, construction, manufacture and testing, documentation and marking of compressors, including integral accessories, e.g. shut-off valve, if necessary.the requirements in this standard take account of the intended use, as defined in 3.12 of en iso 12100-1:2003.this standard relates to the compressor itself which is to be incorporated in a refrigerating system.this standard is not applicable to compressors as defined in the scope which are manufactured before the date of publication as en.2normative referencesthe following referenced documents are indispensable for the application of this document. for dated references, only the edition cited applies. for undated references, the latest edition of the referenced document (including any amendments) applies.en 287-1, qualification test of welders fusion welding part 1: steelsen 294, safety of machinery safety distance to prevent danger zones being reached by the upper limbsen 378-1:2008, refrigerating systems and heat pumps safety and environmental requirements part 1: basic requirements, definitions, classification and selection criteriaen 378-2:2008, refrigerating systems and heat pumps safety and environmental requirements part 2: design, construction, testing, marking and documentationen 378-3, refrigerating systems and heat pumps safety and environmental requirements part 3: installation site and personal protectionen 378-4, refrigerating systems and heat pumps safety and environmental requirements part 4: operation, maintenance, repair and recoveryen 837-1, pressure gauges part 1: bourdon tube pressure gauges dimensions, metrology, require- ments and testingen 837-3, pressure gauges part 3: diaphragm and capsule pressure gauges dimensions, metrology, requirements and testingen 953, safety of machinery guards general requirements for the design and construction of fixed and movable guardsen 1050, safety of machinery principles for risk assessmenten 1515 (all parts), flanges and their joints boltingen 1561, founding grey cast ironsen 1563, founding spheroidal graphite cast ironsen 1779, non-destructive testing leak testing criteria for method and technique selectionen 10045-1, metallic materials charpy impact test part 1: test methoden 10204, metallic products types of inspection documentsen 12178, refrigerating systems and heat pumps liquid level indicating devices requirements, testing and markingen 12516-2, industrial valves shell design strength part 2: calculation method for steel valve shellsen 13136:2001, refrigerating systems and heat pumps pressure relief devices and their associated piping methods for calculationen 13445-2:2002, unfired pressure vessels part 2: materialsen 13445-3, unfired pressure vessels part 3: designen 20898 (all parts), mechanical properties of fastenersen 60034-1:2004, electrical rotating machinery part 1: rating and performance (iec 60034-1:2004)en 60204-1:2006, safety of machinery electrical equipment of machines part 1: general requirements(iec 60204-1:2005, modified)en 60335-2-34, household and similar electrical appliances safety part 2-34: particular requirements for motor-compressors (iec 60335-2-34:2002)en 60529, degrees of protection provided by enclosures (ip code) (iec 60529:1989)en 60947-4-1, low-voltage switchgear and controlgear part 4-1: contactors and motor-starters electromechanical contactors and motor-starters (iec 60947-4-1:2000)en 60999 (all parts), connecting devices electrical copper conductors safety requirements for srew- type and screwless-type clamping unitsen 61010-1, safety requirements for electrical equipment for measurement, control and laboratory use part 1: general requirements (iec 61010-1:2001)en iso 898 (all parts), mechanical properties of fasteners made of carbon steel and alloy steelen iso 4126-2, safety devices for protection against excessive pressure part 2: bursting disc safety devices (iso 4126-2:2003)en iso 9606-2, qualification test of welders fusion welding part 2: aluminium and aluminium alloys(iso 9606-2:2004)en iso 12100-1:2003, safety of machinery basic concepts, general principles for design part 1: basic terminology, methodology (iso 12100-1:2003)en iso 12100-2:2003, safety of machinery basic concepts, general principles for design part 2: technical principles (iso 12100-2:2003)en iso 15607, specification and qualification of welding procedures for metallic materials general rules(iso 15607:2003)en iso 15614-1, specification and qualification of welding procedures for metallic materials welding procedure test part 1: arc and gas welding of steels and arc welding of nickel and nickel alloys (iso 15614-1:2004)en iso 15614-2, specification and qualification of welding procedures for metallic materials welding procedure test part 2: arc welding of aluminium and its alloys (iso 15614-2:2005)cr iso 15608:2000, w