羧甲基淀粉鈉美國藥典30版標(biāo)準(zhǔn).doc

羧甲基淀粉鈉 美國藥典30版標(biāo)準(zhǔn)Sodium Starch Glycolate Starch carboxymethyl ether, sodium salt. Sodium Starch Glycolate is the sodium salt of a carboxymethyl ether ofstarch or of a cross-linked carboxymethyl ether of starch. It may contain notmore than 7.0 percent of Sodium Chloride. The pH and assayrequirements for Type A and Type B are set foHTh in the accompanyingtable。Packaging and storage Preserve in well-closed containers, preferably protected from widevariations in temperature and humidity, which may cause caking.Labeling Label it to indicate the botanical source of the starch from which it was derived, thecross-linking agent (if used), the pH range, and whether it is Type A or Type B.USP Reference standards 11 USP Sodium Starch Glycolate Type A RS.USP Sodium Starch Glycolate Type B RS.IdentificationA: Infrared Absorption 197K .B: A slightly acidified solution of it is colored blue to violet by the addition of iodine andpotassium iodide TS 1.C: To a 2-mL poHTion of the solution prepared for the test for Limit of iron, add 4 mL ofPotassium pyroantimonate solution. If necessary, rub the inside of the test tube with a glassrod. A white, crystalline precipitate is formed.Potassium pyroantimonate solutionTo 2 g of potassium pyroantimonate add 100 mL ofwater. Boil the solution for about 5 minutes, cool quickly, and add 10 mL of a solution ofpotassium hydroxide (3 in 20). Allow to stand for 24 hours, and filter.D: Sodium Starch Glycolate impaHTs an intense yellow color to a nonluminous flame.Microbial limits 61 It meets the requirements of the tests for absence of Salmonellaspecies and Escherichia coli.pH 791 Disperse 1 g in 30 mL of water. The pH of the resulting suspension is eitherbetween 5.5 and 7.5 for Type A or between 3.0 and 5.0 for Type B.Loss on drying 731 Dry it at 130 for 90 minutes: it loses not more than 10.0% of itsweight.Heavy metals, Method II 231 : 0.002%.Limit of ironStandard solution Dissolve 863.4 mg of ferric ammonium sulfate FeNH4(SO4)212H2O inwater, add 25 mL of 2 N sulfuric acid, dilute with water to 500.0 mL, and mix. Pipet 10 mL ofthis solution into a 100-mL volumetric flask, dilute with water to volume, and mix. Pipet 5 mL ofthis solution into a 100-mL volumetric flask, dilute with water to volume, and mix. This solutioncontains the equivalent of 1.0 g of iron per mL.Test solution NOTEReserve a poHTion of this solution for Identification test C. Place 2.5 gin a silica or platinum crucible, and add 2 mL of 10 N sulfuric acid. Heat on a water bath, thencautiously raise the temperature progressively over an open flame. Ignite, preferably in amuffle furnace, at 600 25 . Continue heating until all black paHTicles have disappeared. Cool,add a few drops of 2 N sulfuric acid, and heat and ignite as above. Add a few drops of 2 Mammonium carbonate, evaporate to dryness, and ignite as above. Cool, dissolve the residue in50 mL of water, and mix.Procedure Treat the Test solution and the Standard solution as follows. Transfer 10 mL ofthe solution to a suitable beaker, add 2 mL of citric acid solution (1 in 5) and 0.1 mL ofthioglycolic acid, and mix. Render the solution alkaline, using litmus * as an externalindicator, by the addition of ammonium hydroxide, dilute with water to 20 mL, and mix. Allowthe solutions to stand for 5 minutes: the color of the solution from the Test solution is a shadeof pink no deeper than that of the solution from the Standard solution (0.002%).Limit of sodium chloride Transfer to a beaker about 500 mg of Sodium Starch Glycolate,accurately weighed, and suspend in 100 mL of water. Add 1 mL of nitric acid. Titrate with 0.1 Nsilver nitrate VS, determining the endpoint potentiometrically, using a suitable silver-basedindicator electrode and a double-junction reference electrode containing a 10% potassiumnitrate filling solution in the outer jacket and a standard filling solution in the inner jacket. EachmL of 0.1 N silver nitrate is equivalent to 5.844 mg of sodium chloride.Limit of sodium glycolate NOTEConduct this test without exposure to daylight. Use lowactinicglassware.Standard solution Transfer 310 mg of glycolic acid, previously dried over phosphoruspentoxide in a desiccator at room temperature overnight, to a 500-mL volumetric flask, anddissolve in and dilute with water to volume. Transfer 5.0 mL of this solution to a 100-mLbeaker, add 4 mL of 6 N acetic acid, and allow to stand for about 30 minutes. Add 50 mL ofacetone and 1 g of sodium chloride, mix, and pass through fast filter * moistened withacetone into a 100-mL volumetric flask. Rinse the beaker and filter * with acetone.Combine the filtrate and washings, dilute with acetone to volume, and mix. Allow to stand for24 hours without shaking. Use the clear supernatant as the Standard solution.Test solution Transfer 200 mg, accurately weighed, to a 100-mL beaker Add 4 mL of 6 Nacetic acid and 5 mL of water. Stir until dissolution is complete (about 10 minutes). Add 50 mLof acetone and 1 g of sodium chloride, mix, and pass through fast filter * moistened withacetone into a 100-mL volumetric flask. Rinse the beaker and filter * with acetone.Combine the filtrate and washings, dilute with acetone to volume, and mix. Allow to stand for24 hours without shaking. Use the clear supernatant as the Test solution.Procedure Treat the Test solution and the Standard solution as follows. Heat 2.0 mL of thesolution on a water bath for 20 minutes to remove the acetone. Cool to room temperature.Prepare a 2,7-dihydroxynaphthalene solution as follows. Dissolve 10 mg of 2,7-dihydroxynaphthalene in 100 mL of sulfuric acid, allow to stand until decolorized, and usewithin 2 days. Add 20.0 mL of this 2,7-dihydroxynaphthalene solution to the solution under test,mix, and heat on a water bath for 20 minutes. Cool under running water, and quantitativelytransfer to a 25-mL volumetric flask. Maintain the flask under running water, and dilute withsulfuric acid to volume. Within 10 minutes determine the absorbance of the solution at 540 nmwith a suitable spectrophotometer, using water as the blank: the absorbance of the solutionfrom the Test solution is not more than that of the solution from the Standard solution (2.0%).Assay Transfer about 1 g to a conical flask, add 20 mL of 80% alcohol, stir for 10 minutes,and filter. Repeat the extraction until the chloride has been completely extracted, as shown bya test with silver nitrate. Dry the insoluble poHTion at 105 to constant weight, and transfer anaccurately weighed poHTion (about 700 m