MATLAB擬合多孔介質參數-fluent計算慣性阻力系數和粘性阻力系數

MATLAB擬合多孔介質參數，fluent計算慣性阻力系數和粘性阻力系數包涵：1，MATLAB調取NISTrefprop物性參數；2，MATLAB擬合多孔介質實驗參數（二次函數，參數項目為0）3，按fluent計算公式計算慣性阻力系數和粘性阻力系數步驟：一、根據需要安裝refprop物性參數和MATLAB調用連接（物性參數也可手動輸入不用安裝refprop）1)下載refprop并安裝，2)下載如下4個文件到新建的MATLAB程序保持目錄下:二、建立實驗參數數據表excl文件。實驗名稱與matlab調用名稱一致，實驗數據自己根據實驗數據填寫三、編寫MATLAB程序沒有安裝refprop沒有安裝refprop物性參數可直接激活輸入值結果顯示：調取的空氣物性擬合的二次函數值：Fluent軟件多孔介質中慣性阻力系數C2和粘性阻力系數DFluent軟件中輸入程序：filename1='D:\porous\?à?×?é?êêμ?é2?êy.xlsx'[F1]=importdata(filename1)%êy?Yμ?è????ó?D%V=F1.data(:,1);%?áè??ù?èm/s%P=F1.data(:,2);%?áè??1?μPa%L=F1.data(1,3);%?áè??à?×?é?ê3¤?è%symsxf=fittype('a*x*x+b*x','independent','x','coefficients',{'a','b'});cfun=fit(V,P,f)%??ê??ao?oˉêy￡?êy?Y±?D??aáD?òá?D?ê?xi=0:1:40;yi=cfun(xi)';N=polyfit(xi,yi,2)figureplot(V,P,'r*',xi,yi,'b-');%?ao??ú??oíêμ?é2?êyμ?title('?ao?oˉêyí?D?');%figure%plot(x,sqrt(y-yi(1:1:18,:).^2/18),'r*');%title('±ê×??ó2?í?');[rho,u,Cp,lamda]=refpropm('DVCL','T',273.15+20,'P',101.15,'air.mix')%μ÷è?NISTèí?trefprop2?á???D?%20??￡?±ê????2?á???D?%rho=input('ê?è??ü?èkg/m3:')%N=[3.307,70.08]%L=input('ê?è??à?×??óò3¤?èm:')%u=input('ê?è??ˉá|?3?è?μêyPa*s:')C2=N(1)/(rho*L/2)%1?D?×èá|?μêyC2%%%C2=solve('C2*rho*L/2-N(1)=0')%1?D?×èá|?μêyC2%D=N(2)/u/L%?3D?×èá|?μêy