Brocade7800FCIP配置手冊

1、Brocade7800 FCIP配置手冊目錄一、環境1二、清除GE口原有信息2三、配置GE口類型3四、創建ge0與ge1口IP3五、創建IP路由3六、創建FCIP隧道4七、添加Circuit（電路）5八、配置傳輸壓縮5九、建立lsan zone6十、測試數據復制7一、 環境BJSC-7800-01BJSC-7800-027800-01RJ45RJ45FCFC7800-02RJ45RJ45FCFC7800-01RJ4510.0.100.1RJ4510.0.10.17800-02RJ4510.0.100.2RJ4510.0.10.2二、 清除GE口原有信息BJSC-7800-02:admin po

2、rtshow fcipcircuit all 顯示電路信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 InProg -s 1m27s 0.00 0.00 4 20/100 0 16 1 ge1 InProg -s 18m14s 0.00 0.00 4 30/90 0- Flags: circuit: s=sack有2條電路，分別是16 0與16 1BJSC-7800-02:admin portcfgdefault ge0直接清除ge0口信息失敗Circuit Configur

3、ation exists using this GE port.BJSC-7800-02:admin portcfg fcipcircuit 16 delete 0需要先刪除電路Operation SucceededBJSC-7800-02:admin portcfgdefault ge0清除ge0口信息成功Operation SucceededBJSC-7800-02:admin portcfgdefault ge1同上Circuit Configuration exists using this GE port.BJSC-7800-02:admin portcfg fcipcircuit

4、16 delete 1同上Operation SucceededBJSC-7800-02:admin portcfgdefault ge1同上Operation SucceededBJSC-7800-02:adminportcfg fciptunnel 16 delete刪除隧道shwitchshow顯示GE口結果 ge0 cu 1G Online FCIP Copper ge1 cu 1G Online FCIP Copper ge2 id 1G No_Light FCIP ge3 - 1G No_Module FCIP ge4 - 1G No_Module FCIP ge5 - 1G No

5、_Module FCIPge0電口ge1電口光口光口Ge2光口Ge3光口Ge4光口Ge5光口當上面2個電口被使用后，下面的前2個光口將不能使用。三、 配置GE口類型BJSC-7800-01:admin portcfggemediatype Usage: portcfggemediatype GbE_port optical 光| copper電 BJSC-7800-01:admin BJSC-7800-01:admin 例如：sw67:adminportcfggemediatype GE0 optical四、 創建ge0與ge1口IPBJSC-7800-01:adminportcfg ipif

6、 ge0 create 10.0.100.1 255.255.255.0 1500BJSC-7800-01:admin portcfg ipif ge1 create 10.0.10.1 255.255.255.0 1500BJSC-7800-01:admin portshow ipif all 顯示GE口IPPort: ge0Interface IPv4 Address NetMask Effective MTU Flags- 0 10.0.100.1 255.255.255.0 1500 U R M Port: ge1Interface IPv4 Address NetMask Effec

7、tive MTU Flags- 0 10.0.10.1 255.255.255.0 1500 U R M Flags: U=Up B=Broadcast D=Debug L=Loopback P=Point2Point R=Running N=NoArp PR=Promisc M=Multicast S=StaticArp LU=LinkUpBJSC-7800-01:admin對端BJSC-7800-02配置IP為GE0 10.0.100.2 GE1 10.0.10.2五、 創建IP路由測試環境直連方式可以ping通對端，因此配置路由步驟可先忽略。實際實施時不可省略此步。BJSC-7800-0

8、1:admin portcmd -ping ge0 -s 10.0.100.1 -d 10.0.100.2Pinging 10.0.100.2 from ip interface 10.0.100.1 on 0/ge0 with 64 bytes of dataReply from 10.0.100.2: bytes=64 rtt=2ms ttl=20Reply from 10.0.100.2: bytes=64 rtt=0ms ttl=20Reply from 10.0.100.2: bytes=64 rtt=0ms ttl=20Reply from 10.0.100.2: bytes=64

9、 rtt=2ms ttl=20Ping Statistics for 10.0.100.2: Packets: Sent = 4, Received = 4, Loss = 0 ( 0 percent loss) Min RTT = 0ms, Max RTT = 2ms Average = 1msBJSC-7800-01:admin六、 創建FCIP隧道在第16VE口創建FCIP隧道(先寫遠端IP再寫本端IP,后面的數字單位是K)，兩邊都要?jiǎng)?chuàng)建BJSC-7800-01:admin portcfg fciptunnel 16 create 10.0.100.2 10.0.100.1 -b 500

10、00 -B 100000Operation Succeeded當僅僅本端建立好后，狀態為InProgBJSC-7800-01:admin portshow fciptunnel all 顯示隧道信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 - InProg - 0s 0.00 0.00 0 - - Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FICON T=TPerf circuit: s=sackBJSC-7

11、800-01:admin portshow fcipcircuit all 顯示電路信息- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 InProg -s 0s 0.00 0.00 0 50/100 0- Flags: circuit: s=sack當對端也建立好隧道后，狀態為UpBJSC-7800-01:admin portshow fciptunnel all- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCn

12、t CommRt Met- 16 - Up - 3m40s 0.10 0.01 1 - - Flags: tunnel: c=compression f=fastwrite t=Tapepipelining F=FICON T=TPerf circuit: s=sackBJSC-7800-01:admin portshow fcipcircuit all- Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 Up -s 3m49s 0.07 0.01 1 50/100 0- Flags:

13、 circuit: s=sackBJSC-7800-01:admin創建好隧道后，0電路也就存在了，并且已經存在于16隧道中。下面要添加1電路到16隧道中。七、 添加Circuit（電路）將Circuit（電路）放到16隧道,編號為1。BJSC-7800-01:admin portcfg fcipcircuit 16 create 1 10.0.10.2 10.0.10.1 -b 50000 -B 100000Operation SucceededBJSC-7800-01:admin兩邊都要操作添加，第一個IP為目標，第二個IP為本地BJSC-7800-01:admin portshow fc

14、ipcircuit all - Tunnel Circuit OpStatus Flags Uptime TxMBps RxMBps ConnCnt CommRt Met- 16 0 ge0 Up -s 22m22s 0.02 0.01 2 50/100 0 16 1 ge1 Up -s 10s 0.00 0.00 1 50/100 0- Flags: circuit: s=sackBJSC-7800-01:admin八、 配置傳輸壓縮兩邊都要改, 建議使用中等壓縮比，數字表示為2,高壓縮比是3，不建議3.也不建議1.BJSC-7800-01:admin portcfg fciptunnel

15、16 modify -c 2九、 建立lsan zone兩邊都要建立BJSC-7800-01:admin zonecreate lsan_zone,50:06:0e:80:04:29:3f:12;50:06:0e:80:04:29:3f:32Zone成員的wwn來自兩臺7800所接的存儲78001為4 4 010400 id N2 Online FC F-Port 50:06:0e:80:04:29:3f:1278002為4 4 010400 id N2 Online FC F-Port 50:06:0e:80:14:38:cc:11BJSC-7800-01:admin cfgcreate l

16、san_cfg,lsan_zoneBJSC-7800-01:admin cfgenable lsan_cfgBJSC-7800-01:admin cfgshowDefined configuration: cfg: lsan_cfg lsan_zonezone: lsan_zone 50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11Effective configuration: cfg: lsan_cfg zone: lsan_zone 50:06:0e:80:04:29:3f:12 50:06:0e:80:14:38:cc:11BJSC-780

17、0-01:admin添加其他存儲端口到lsan_zoneBJSC-7800-01:admin zoneadd lsan_zone,50:06:0e:80:04:29:3f:32;50:06:0e:80:14:38:cc:31cfgdisablecfgenableBJSC-7800-01:admin cfgshowDefined configuration: cfg: lsan_cfg lsan_zone zone: lsan_zone 50:06:0e:80:04:29:3f:12; 50:06:0e:80:14:38:cc:11; 50:06:0e:80:04:29:3f:32; 50:06

18、:0e:80:14:38:cc:31Effective configuration: cfg: lsan_cfg zone: lsan_zone 50:06:0e:80:04:29:3f:12 50:06:0e:80:14:38:cc:11 50:06:0e:80:04:29:3f:32 50:06:0e:80:14:38:cc:31BJSC-7800-01:admin十、 測試數據復制HDS工程師在USP存儲配置界面上可以看到2條連路已經連通。新建2個LUN并作數據復制。（截圖略）可以看到數據傳輸信息和壓縮比BJSC-7800-01:admin portshow fciptunnel all

19、 -p-Tunnel ID: 16 Tunnel Description: Admin Status: Enabled Oper Status: Up Compression: On (Moderate) Fastwrite: Off Tape Acceleration: Off TPerf Option: Off IPSec: Disabled Remote WWN: Not Configured Local WWN: 10:00:00:05:33:2d:47:ac Peer WWN: 10:00:00:05:33:31:60:fc Circuit Count: 2 Flags: 0x00000000 FICON: Off Oper Status: Up Flow Ctrl State: Off Connected Count: