




版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、ansys命令中英文解釋2007-03-21源自:IT粉絲網網友評論 0 條進入視頻教程分享一下! BEGINNER'S GUIDE TO ANSYS COMMANDS The symbol '*' corresponds to the following: * -> k, l, a, v, e, n, cm, et, mp, r where => k -> Keypoints l -> Lines a -> Area v -> Volumes e -> Elements n -> Nodes cm -> compo
2、nent et -> element type mp -> material property r -> real constant $ -> d, f, sf, bf, ic, where => d -> DOF constraint (ux. in Structural, Temp in thermal, f -> Force Load ( Heat in thermal) sf -> Surface load on nodes bf -> Body Force on Nodes More Commands can be generat
3、ed by sensible combinations of " $* " family of commands. See the following list of $* possible options $* -> dk -> DOF constraints on KP (Vx,Vy,Pres. in CFD) dl -> DOF constraints on Lines da -> DOF constraints on Areas fk -> Force on Keypoints sfl -> Surface load on Lin
4、es sfa -> Surface load on Areas sfe -> Surface load on element faces bfk -> Body Force on Keypoints bfl -> Body Force on Lines bfa -> Body Force on Area bfv -> Body Force on Volumes bfe -> Body Force on Elements ic -> Initial Conditions ", p" -> If ",p"
5、 was issued at the end of the Command(in Input Window) the GUI based picking menu will be activated. Useful for listing, plotting, meshing, deleting, etc. * 1. Listing of picked Entities: COMMAND SYNTAX: *LIS,p & $*LIS,p A few Combinations of this command are: klis,p -> List KP llis,p -> L
6、ists Lines alis,p -> Lists Areas vlis,p -> Lists Volumes elis,p -> Lists Elements nlis,p -> Lists Nodes cmlis,p -> Lists components cslis,p -> Lists user created local co-ordinate systems dlis,p -> Lists DOF constraints specfied on nodes dalis,p -> Lists DOF constraints appli
7、ed on Areas flis,p -> Lists force on Nodes sfllis,p -> Lists Surface Load on lines bfalis,p -> Lists body force load applied on Areas iclis,p -> Lists Initial condition on Nodes If ",p" was not issued, all entites currently selected will be listed. For certain commands ",p
8、" cannot be issued. See the below mentioned commands etlis -> Lists the different element types defined mplis -> Lists whatever Material properties rlis -> Lists whatever real constants cslis -> Lists all co-ordinate systems cmlis -> Lists all components * 2. Plotting of Entities
9、: COMMAND SYNTAX: *plo KPLO / LPLO / APLO / VPLO / EPLO / NPLO / CMPLO / * 3. deleting of Entities: COMMAND SYNTAX: *DEL,p & $*DEL,p KDEL,p / LDEL,p / ADEL,p / VDEL,p / EDEL,p / NDEL,p / CMDEL,p / DDEL,p / DKDEL,p / DADEL,p / FDEL,p / SFDEL,p / SFEDEL,p / SFADEL,p / SFLDEL,p / BFADEL,p / . The s
10、yntax for this command is very similar to LISTING command. * 4. distance between two entities: COMMAND SYNTAX: *DIS,p ndis,p -> Distance between two nodes kdis,p -> Distance between two KPs * 5. Meshing of geometries: COMMAND SYNTAX: *MES,p KMES,p / LMES,p / AMES,p / VMES,p * 6. Size settings
11、for Lines and Areas before meshing : COMMAND SYNTAX : *size,p Lesiz,p / Aesize,p * 7. Clearing Meshes of already meshed geometries: COMMAND SYNTAX: *CLE,p KCLE,p / LCLE,p / ACLE,p / VCLE,p * 8. BOOLEAN Operations: Intersect COMMAND SYNTAX : *IN* AINA,p / VINV,p / LINL,p / AINV,p / LINV,p / LINA,p *
12、9. BOOLEAN Operations: GLUE COMMAND SYNTAX : *GLUE VGLUE,p / AGLUE,p / LGLUE,p * 10. Boolean Operations: SUBTRACT/DIVIDE: COMMAND SYNTAX: *sb*,p See the following examples to understand how this works: asba,p -> Subtract Area from Area asbl,p -> Divide Area by line vsba,p -> Divide volume b
13、y Area lsbw,p -> Divide line by Workplane vsbw,p -> Divide volume by Workplane asbw,p -> Divide area by Workplane vsbv,p -> subtract Volume by another volume More combinations exist. The user needs to explore them for themselves -> forms a part of learning * 11. Boolean Operations: Ov
14、erlap: COMMAND SYNTAX: *OVLAP,p AOVLAP,p / VOVLAP,p * 12. Concatenation of Lines / Areas -> for map meshing COMMAND SYNTAX : *ccat,p LCCAT,p -> Concatenation of Lines for Map meshing Area ACCAT,p -> Concatenation of Areas for Map meshing Volume * 13. Dragging operation COMMAND SYNTAX : *dra
15、g,p vdrag,p -> Drag areas along a line to create a new volume adrag,p -> Drag line along a line to create a new area ldrag,p -> Drag KP along a line to create a new line * 14. Copy Geomtric entities COMMAND SYNTAX : *GEN,p KGEN,p / LGEN,p / AGEN,p / VGEN,p Please note that *GEN commands are
16、 also used for MOVE operations. The difference lies in the value specified in the 10th field of these *GEN commands. By default it is 0 -> which does the COPY operation. If specfied as 1 -> it does the MOVE operation * 15. Bottom -to- Top modeling commands: COMMAND SYNTAX : *,p & *,p k,p -
17、> Allows user to pick KP in the Workplane l,p -> Create lines from existing KP ak,p -> Create area from KP al,p -> Create area from lines v,p -> Create Volume from KP va,p -> Create Volume from Areas e,p -> Create Elem from existing nodes en,p -> Create Elem from nodes * 16.
18、To apply common Boundary Conditions such as DOF constraint, Forces, Surface Loads, Bodyforce Loads and Initial conditions * -> is meant for the KLAVE entities only (KLAVEN stands for KP, Lines, Area, Volumes & ELem ) 16a. DOF constraint : COMMAND SYNTAX : $*,p ( Please Note: NOT all * are val
19、id) See the valid combinations below: D,p -> To apply DOF on nodes DK,p -> To apply DOF on Keypoints DL,p -> Apply DOF on Lines DA,p -> Apply DOF on Areas ( symmetry or Anti-symmetry will be prompted) * 16b. FORCE Loading: COMMAND SYNTAX : $*,p See the valid combinations below: f,p ->
20、 Forces on nodes fk,p -> Force on Keypoints (fa,p or FV,p or FL,p -> Since force cannot be applied on Lines or Area & volumes. this command does not exist.) * 16c. Surface Loads: COMMAND SYNTAX : $*,p See the valid combinations below: sf,p -> Surface Load on a set of Nodes sfl,p -> S
21、urface Load on Lines sfa,p -> Surface Load on Area sfe,p -> Surface Load on Element (SFk,p and SFV,p do not exist since pressure cannot be applied on a single Kp and neither can it be applied on a volume) * 16d. BodyForce Load: COMMAND SYNTAX : bf*,p See the valid combinations below: bf,p ->
22、; Bodyforce Load on a set of Nodes bfk,p -> Bodyforce Load on KP bfl,p -> Bodyforce Load on Lines bfa,p -> Bodyforce Load on Areas bfv,p -> Bodyforce Load on Volumes bfe,p -> Bodyforce Load on Element * 16e. Initial conditions: ic,p -> Initial Conditions on Nodes (P.S: Initial Cond
23、itions can be applied only to nodes. ) * 17. To refine a mesh : COMMAND SYNTAX : *ref,p kREF,p / kREF,p / aREF,p / eREF,p / nREF,p * 18. To TRANsfer loads from the Solid model to the FE model: COMMAND SYNTAX : $TRAN dtran / ftran / sftran / bftran & SBCTRAN (SBCTRAN -> Transfers all solid mod
24、el loads to FE model) * 19. Writing / Reading information to a file (ASCII) COMMAND SYNTAX : *read, & *write, NWRITE / MPWRITE / ETWRITE / RWRITE / EWRITE / CDWRITE NREAD / MPREAD / ETREAD / RREAD / EREAD / CDREAD / LDREAD (Some of these commands ETWRITE/ETREAD , RWRITE/RREAD are undocumented. B
25、ut they do work) The Commands CDWRITE and CDREAD are used to write/read all FE model related info (w or w/o geometry to ASCII files) Its recommended the user read the online help on these two commands before using them The LDREAD commands are used to read loads (LD) from other analysis types. For example: Temp from Thermal results file (*.rth) are applied onto
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 模型評選大賽活動方案
- 榴蓮低價活動方案
- 沙龍現場活動方案
- 汽車加油站打折活動方案
- 永嘉三八活動方案
- 植樹活動策劃方案
- 武漢校園招聘活動方案
- 河北招商活動方案
- 民族品酒活動策劃方案
- 夢想自律活動方案
- 2025至2030中國合規行業發展趨勢分析與未來投資戰略咨詢研究報告
- 【人教版】河北石家莊2024-2025學年 四年級下學期期末數學試題【一】有解析
- 2025至2030年中國石晶地板行業市場現狀調查及投資前景研判報告
- 2025年衛生系統招聘考試《職業能力傾向測試》新版真題卷(附詳細解析)
- 2025-2030年中國下一代測序(NGS)數據分析行業市場現狀供需分析及投資評估規劃分析研究報告
- 帶鋼熱軋智能控制系統
- 智能安全帽在智慧工地中的應用與管理平臺研究
- Machine-Cmk-設備能力指數Cmk分析表
- 情侶共同存錢協議書
- DB65∕T 3952-2016 反恐怖防范設置規范 學校
- 科研助理合同協議書
評論
0/150
提交評論