AP3010DN-AGN設置為普通無線路由器操作步驟

1、實用文檔華為 AP3010DN-AGN無線 AP 設定為一般胖 AP無線路由器模式 操作步驟說明文檔1, 認識硬件實用文檔實用文檔實用文檔實用文檔實用文檔除以上之外，還需要普通網線 1 條，電腦 1臺2, 所用到的軟件操作系統 xp 或 win7Xmanager4漢化版實用文檔USB轉 COM線驅動TFTP軟件 3CDaemon漢化版AP升級固件的文檔 FatAP3X10XN_V200R005C00SPC600.bin3, 操作步驟：第一步，復位 AP，刷固件 FatAP3X10XN_V200R005C00SPC600.bin第二步，登錄 AP的 WEB管理頁面創建 WIFI 并建立 DHCP

2、第三步，創建 WAN口并與 LAN口關聯下面分步詳細說明 準備軟件，依次安裝 USB轉 COM驅動，Xmanager4漢化版，將 TFTP軟件 3CDaemon漢化 版復制到 C盤，并變更文件夾名稱為 TFTP，路徑如 C:TFTP ，把 AP 的固件 FatAP3X10XN_V200R005C00SPC600.b復in制到 C:TFTP 目錄中給 AP接上 12V2A的電源， 此時不要接 POE供電模塊，注意！復位后將消除全部配 置及密碼。 等啟動完畢后，用尖銳物按下復位口 10 秒后松開， AP開始重新啟動， AP 的指示燈變?yōu)殚L亮啟動狀態， 之后指示燈變?yōu)殚W爍狀態完成復位。 完成復位后接

3、上 USB 轉串口線，連接電腦 USB口和 AP的 Console 口，打開 Xmanager4中的 Xshell4 ，新建 會話窗口選擇 SERIAL配置波特率 9600 及 COM端口號正確實用文檔連接成功后會顯示Please configure the login password (/)Enter password:這是初次登錄要求設定密碼，密碼復雜度要求為英文加數字，最小 8 位，我們暫定 密碼 hua88888 填寫兩次密碼后顯示如下Enter password:Confirm password:這表示已經成功設定了管理密碼， 以上設定的密碼僅限于連接 Console 口使用，和

4、WEB管理界面不是同一個密碼， WEB管理界面密碼下面會提到。使用 1 條一般使用的網線，一端連接電腦，一端連接 AP的 ETH/PoE口，此時不要拔 掉 Console 口上的串口線，不要拔掉 12V 電源，不要連接 POE供電模塊， 配置電腦有 線網卡的 IP 地址為 00 子網掩碼 網關 DNS 空 白不填寫，去我的電腦打開 C:TFTP 目錄，打開 3CDaemon.EXE點擊設置 TFTP服務器 按鈕，按照下圖設置路徑實用文檔然后回到 Xshell4 窗口，會顯示Please check whether syste

5、m data has been changed, and save data in timeConfiguration console time out, please press any key to log on 是因?yàn)槌瑫r(shí)登出，需要重新填寫密碼登錄，重新登錄后按照以下腳本操作， 整個過 程不要關閉 3CDaemon.EXEsys # 鍵入實用文檔Enter system view, return user view with Ctrl+Z.Huawei ap-mode-switch prepare # 鍵入Info: Prepare is ok, Use ap-mode-switch c

6、ommand to switch to fit ap.Huawei ap-mode-switch check # 鍵入Info: Ap-mode-switch check ok.Huawei ap-mode-switch tftp FatAP3X10XN_V200R005C00SPC600.bin 00 # 鍵入 Info: Preparing to upgrade. Please wait a moment Warning: System will reboot, if you want to switch to upgrade-assistant-package.Ar

7、e you sure to execute these operations ? Y/N:y # 這里是提示整個過程會重啟，鍵入 yInfo: system is rebooting ,please wait.Try hardware rebooting.Welcome To HUAWEI AP WorldUBoot V200R005 version-125 (Aug 1 2014 - 04:33:21) DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus Test in 1 Seconds: 0 Flash: 3

8、2 MBPCIE: PCIe Clock 40MHz Ethernet Mac: B4-15-13-F8-82-20Image: Current Bootup is B Image: Current Bootup is BCurrent master bootup parameter area is A Boot Kernel A Address: 0x9f3fb000 Boot Kernel B Address: 0x9f840000 Press j or J to stop Bus-Test in 1 seconds: 0 Bus test starting.PCIE bus test O

9、K. SPI bus test OK. DDR bus test OK. RGMII bus test OK. Bus test ending.Save Bus Test Result SuccessfulPress f or F to stop Auto-Boot in 3 seconds: 0 Uncompressing Kernel Image . OKStarting kernel .Booting Atheros AR934x init_bsp_adapter .OK. mm_init .OK. sched_init .OK. softirq_init .OK. console_in

10、it .OK. thread_info_cache_init .OK. fork_init .OK. dbg_late_init .OK. imv_init_complete .OK.實用文檔Linux version 3-WR_standard (gcc version 4.5.2 (Sourcery CodeBench Lite 2011.03-93) )#2 PREEMPT Fri Nov 7 17:34:15 CST 2014flash_size passed from bootloader = 32 MBarg 1: console=ttyS0,9600

11、arg 2: root=/dev/mtdblock10arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5:mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(conf igA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs);arg 6: mem

12、=126Math_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges:Normal 0x00000000 - 0x00007e00Movable zone start PFN for each nodeearly_node_map1 active PFN ranges0: 0x00000000 - 0x00007e00Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32004Kernel command

13、 line: console=ttyS0,9600 root=/dev/mtdblock10 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(conf igA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs); mem=126

14、MPrimary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesFWD_MEM: aligned address 82000000FWD_MEM: 02000000FWD_MEM: Allocating 21MB (5568 pages) of memory at addr 82000000the pci irq_base value: 70 plat_time_init:doneMount-

15、cache hash table entries: 512Registering WDTdoneath_pcibios_init: bus 0PCI init:doneath_pcibios_init(234): PCI 0 CMD write: 0x356 registering PCI controller with io_map_base unsetbio: create slab at 0 SCSI subsystem initialized pcibios_map_irq: IRQ 70 for bus 0 ath_init_ioctldoneinit_vdso successful

16、l mtd: no mtd-id ath_flash_initdonemii_bus 0 successed to registerRegistering OTPdoneRegistering Clock Switch Interfacedonestarting pid 42, tty : /etc/init.d/rcS MIMC_KERNEL: Module init.enable_rx 1250: init_phy_eee: control = 0x1000FatAP3X10XN_V200R005 100% |*| 21377k 00:00:00 ETA. #這里開始上傳固件，之后繼續重啟

17、Error: Upgrade failed due to a type mismatch.starting pid 149, tty : /sbin/swapoff -a cant run /sbin/swapoff: No such file or directory starting pid 150, tty : /bin/umount -a -r umount: tmpfs busy - remounted read-only umount: none busy - remounted read-only umount: /proc busy - remounted read-only

18、The system is going down NOW!Sent SIGTERM to all processes Sent SIGKILL to all processes Requesting system reboot Restarting system.Try hardware rebooting.實用文檔Welcome To HUAWEI AP WorldUBoot V200R005 version-125 (Aug 1 2014 - 04:33:21)DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus

19、 Test in 1 Seconds: 0Flash: 32 MBPCIE: PCIe Clock 40MHzEthernet Mac: B4-15-13-F8-82-20Image: Current Bootup is AImage: Current Bootup is ACurrent master bootup parameter area is BBoot Kernel A Address: 0x9f3fb000Boot Kernel B Address: 0x9f840000Press j or J to stop Bus-Test in 1 seconds: 0Bus test s

20、tarting.PCIE bus test OK.SPI bus test OK.DDR bus test OK.RGMII bus test OK.Bus test ending.Save Bus Test Result SuccessfulPress f or F to stop Auto-Boot in 3 seconds: 0Uncompressing Kernel Image . OKStarting kernel .Booting Atheros AR934xinit_bsp_adapter .OK.mm_init .OK.sched_init .OK.softirq_init .

21、OK.console_init .OK.thread_info_cache_init .OK.fork_init .OK.dbg_late_init .OK.imv_init_complete .OK.Linux version 3-WR_standard (gcc version 4.5.2 (Sourcery CodeBench Lite 2011.03-93) )#1 PREEMPT Fri Aug 1 04:16:06 CST 2014flash_size passed from bootloader = 32 MBarg 1: console=ttyS0

22、,9600arg 2: root=/dev/mtdblock5arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5:mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(conf igA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs);arg 6:

23、 mem=126Math_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges:Normal 0x00000000 - 0x00007e00Movable zone start PFN for each nodeearly_node_map1 active PFN ranges0: 0x00000000 - 0x00007e00Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32004Kernel com

24、mand line: console=ttyS0,9600 root=/dev/mtdblock5 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(conf igA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs); mem=

25、126MPrimary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytesFWD_MEM: aligned address 82000000FWD_MEM: 02000000FWD_MEM: Allocating 21MB (5568 pages) of memory at addr 82000000實用文檔the pci irq base value: 70 plat_time_init:don

26、eMount-cache hash table entries: 512Registering WDTdoneath_pcibios_init: bus 0PCI init:doneath_init_ioctldoneinit_vdso successfull mtd: no mtd-idath_flash_initdonemii_bus 0 successed to registerRegistering OTPdoneath_pcibios_init(234): PCI 0 CMD write: 0x356 registering PCI controller with io_map_ba

27、se unset bio: create slab at 0 pcibios_map_irq: IRQ 70 for bus 0Registering Clock Switch InterfacedoneVFS: Mounted root (squashfs filesystem) readonly on device 31:5. starting pid 21, tty : /etc/init.d/rcSMSS_PUB Version 1.07, build on Date : Aug 1 2014, Time : 04:34:12 MIMC_KERNEL: Module init.eth-

28、diag install ok!Drv_ap_api module:InitDisabling lock debugging due to kernel taintMount fsimage type: patchUser fs folder : /optLoop device : /dev/loop0Mount folder : /mnt/patchGet file name from fldesc failed,wrong length(0x50)!AP wa6x5 cap32 start, 04:30:24MSS_PUB Version 1.07, build on Date : Aug

29、 1 2014, Time : 04:30:06 MSS_PUB_Init Succ! u32Ret = 0Module MEM Init OK!Module DIAG Init OK!Module PBUF Init OK!Module IM Init OK!Module IIC Init OK!Module HAL Init OK!Module Timer Init OK!Module TIME Init OK!AP_Board_Cfg Succ! u32Ret = 0MSS_Global_Init Succ! ret = 0MSC Process run on core 0, PID =

30、 66 MSU Process run on core 0, PID = 67 MSC_TCTL_Init Succ! u32Ret = 0 MSC goto scheduler!MSU_InstReg return 0x0 CAP_FWDIF_Init return 0x0 L1_IP_Fast_BaseAddrInit return 0x0 MSU_TableBaseInit return 0x0 MSU Init OKVOS_Start OKVRP_SockTm_Init createOKSystem recover configuration OK!Press any key to g

31、et startedPlease configure the login password (/)Enter password:# 鍵入密碼 hua88888Confirm password:# 鍵入密碼 hua88888display version # 鍵入Huawei Versatile Routing Platform SoftwareVRP (R) software, Version 5.150 (AP3010DN FAT V200R005C00SPC600)#看這里，表示已經更新固件版本成功Copyright (C) 2011-2014 HUAWEI TECH CO., LTDHu

32、awei AP3010DN Router uptime is 0 week, 0 day, 0 hour, 8 minutesMPU 0(Master) : uptime is 0 week, 0 day, 0 hour, 8 minutesSDRAM Memory Size : 128 M bytesFlash Memory Size : 32 M bytesMPU version information :1. PCB Version : H85D2TD1D200 VER.B實用文檔2. MAB Version : 03. Board Type : AP3010DN4. BootROM V

33、ersion : 125至此刷固件 FatAP3X10XN_V200R005C00SPC600.b完in畢。登錄 AP的 WEB管理頁面創建 WIFI 并建立 DHCP現在關閉 3CDaemon.EXE打開電腦的 IE 8 瀏覽器打開地址 用 戶名是 admin 密碼是 登入后點維護 管理員 “操作” 下面的“修改” 變更密碼 hua88888 之后電右上角的保存配置。點配置接口管理 VLANVLANIFVlanif1“操作”下面的“修改”按鈕，按照如下圖 設定， 這里就是設定 LAN口的地址點確定按鈕后會失去連接，去電腦的

34、有線網口更改 IP 地址為 00 子網掩 碼 網關 DNS 空白不填寫，重新打開電腦的 IE 8 瀏覽器， 打開地址 用戶名是 admin 密碼是 hua88888點配置IP業務DHCPDHC狀P態 : 選擇開啟應用 地址池列表下面點“新建“ 見下圖實用文檔然后點上確定按鈕，下圖是 創建 DHCP之后的樣子實用文檔下面創建 WIFI 及 WIFI 密碼點配置 WLAN業務服務集BSS接口BSS接口列表下邊點“新建“按鈕 見下圖點確定建立完畢 BSS接口點安全模板 點安全模板列表下邊的“新建

35、“按鈕 見下圖實用文檔點確定建立完畢安全模板， 其實這里就是創建了 WIFI 密碼及加密方式 點流量模板 流量模板列表下邊的“新建“按鈕 見下圖實用文檔點服務集 服務集列表下邊的“新建“按鈕 見下圖點配置WLAN業務射頻模板 WMM模板WMM模板列表下邊的“新建“按鈕 見下圖實用文檔點射頻模板 射頻模板列表下邊的“新建“按鈕 見下圖點配置WLAN業務無線網絡配置 無線網絡列表下邊的“新建“按鈕 見下圖實用文檔點右上角保存配置按鈕點維護 系統維護 設備管理 接入優先級 : 5G 優先前面的勾去掉 （ 不選擇 ）點應用 按鈕點右上角保存配置按鈕點維護系統維護 設備重啟 點下邊的設備重啟按鈕 點是等

36、待重啟后進入開機正常狀態使用筆記本電腦無線網卡連接 WIFI 信號顯示為 HW001的 AP，密碼是之前上面設定的 12345678 連接成功之后得到 DHCP推送的 IP 地址如下圖表示這一階段設定完成最后一步講解：創建 WAN口并與 LAN口關聯實用文檔模擬一個網絡環境WAN口 IP 為 00 子網掩碼是 網關是 下面要進行操作建立 WAN口， 要新建 VLAN2和 Vlanif2LAN口 IP 為 上面已經建立完畢，屬于 VLAN1和 Vlanif1要說明一點，華為 AP上的 ETH/PoE口就是 Gigabi

37、tEthernet0/0/0下面進行操作重新打開 Xshell4 ，用串口線建立連接，執行以下腳本Login authenticationPassword: # 鍵入密碼sys # 進入特權模式Enter system view, return user view with Ctrl+Z.Huawei vlan batch 2 # 建立 vlan 2Info: This operation may take a few seconds. Please wait for a momentdone.Huawei display vlan # 顯示 vlan 列表* : management-vlanThe total number of vlans is : 2VLAN ID Type Status MAC Learning Broadcast/Multicast/Unicast Property1 common enable enable2 common enable enableforward forward forward forwardforward default forward default#表示已有 vlan 1表示已有 vlan 2Huawei interface Vlanif2 # 建立 Vlanif2 Huawei-Vlanif2 i